BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 10

Page: 10 / 183

Safety and Ergonomics

1-6

Safety and Ergonomics
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Safety Features

Two-handed start-up prevents the tool from being started accidentally.

The air supply is disconnected from the motor when the run lever is released.

Ergonomic Features

Right and Left-Handed

–

The Whizard

AirMax MACH 3 Trimmers have been

manufactured in both right and left-handed configurations.

Optional Thumb Support

A thumb support is available to ensure a proper and comfortable

fit while providing added control and stability of the tool during use.

Additional Features

The hose assembly swivels for easier trimmer rotation and operator comfort.

The hose is ten feet (3.05 m) long to allow for greater operator mobility.

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands