manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 43

 Instructions for Operation 

 

 

Manual No.  188000  
September 1, 2009 

 Instructions for Operation  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

4-19 

 

Blade Changing 

 

 

 

W A R N I N G  

 

 

 

SHARP BLADES MAY CAUSE CUT INJURY! 

 

FOR

 

PROPER

 

PROTECTION

 

OF

 

HANDS,

 

A

 

PROTECTIVE

 

GLOVE

 

SHOULD

 

BE

 

USED

 

WHEN

 

OPERATING

 

THIS

 

EQUIPMENT

 

AND

 

DURING

 

THE

 

HANDLING

 

OF

 

BLADES.

  

 

 

ALWAYS

 

DISCONNECT

 

THE

 

TOOL

 

FROM

 

THE

 

AIR

 

SUPPLY

 

PRIOR

 

TO

 

SERVICING. 

 

The Whizard

® 

AirMax MACH 3 Trimmers have been designed to allow the blades to be quickly 

removed and reinstalled. 

 

To Change the Blade 

 

 

 

Loosen only the left cover retaining screw. 

 

 

NOTE

:

  Slight tension on the left cover screw will allow the blade housing to stay open.

 

 

 

Holding the tool blade side up, pry 
open the blade housing with a 
screwdriver. 

 

Carefully remove the old blade. 

 

Insert a new blade in the housing. 

 

 

Left Cover
Retaining
Screw

Screwdriver

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands