manualshive.com logo in svg

Anita GARUDAN GF-2207-147, User Manual, Page: 41 / 53

Share
Download
Anita GARUDAN GF-2207-147 User Manual Download Page 41

© ANITA  

MP03700EN_181101 

 

41 

 

Tension Release: 

 

 

 

 

 

 

 

If the thread slips out of the needle hole after thread 

cutting, or if the tension disc remain open, adjust as 

follows. 

A. If the thread slips out of the needle hole (The tension 

release lever is not working properly during thread 

cutting) 
1. Press the thread trimming solenoid 

①

 and turn the 

sewing machine pulley. 
2. The tension disc 

④

 should be open 0.8mm when the 

tension release lever 

②

 roller reaches the top of the 

tension release cam 

③

. 

3. Make sure the tension disc is open when the tension 
release lever 

②

 roller is at the top of the tension release 

cam 

③

, and closed when the lever roller is on the lever. 

 

B. If the tension disc remain open. 
1. Make sure the tension release lever 

②

 is returned. 

2. Make sure the return spring 

⑥

 is not disengaged. 

Check the above and adjust with nut 

⑤

 as necessary. 

If adjustment is not possible, replace the tension release 
wire 

⑦

.

 

 

 

 

 

 

 

 

 

 

 

 

www.garudan.cz

Summary of Contents for GARUDAN GF-2207-147






















































Reviews:

No comments