manualshive.com logo in svg

Anita GARUDAN GF-2207-147, User Manual, Page: 31 / 53

Share
Download
Anita GARUDAN GF-2207-147 User Manual Download Page 31

© ANITA  

MP03700EN_181101 

 

31 

 

Clearance between rotary hook and opener 

 

 

 
1. Loosen the setscrew 

⑪

 and 

move the opener 

①

 to the left or 

right to adjust so that the 

clearance between the rotary 
hook 

⑦

 and the opener 

⑩

 is 

0.2mm when the opener 

⑩

 is 

pulled as far as it will go in the 

direction of the arrow. 
2. Tighten the set screw 

⑪

. 

 

 

 

Needle bar height and lift amount 

 

 

[GF-2207-147, GF-2207-447] 

 

Needle bar height 

1. Change the stitch length to the 

smallest possible setting. 

2. Open the face plate. 

3. Turn the machine pulley to 
move the needle bar 

⑫

 to its 

lowest position. 

ⓐ

 Reference line 

⑫

 at the top of the needle bar 

must be aligned with the lower 

edge of the needle bar supporter 

⑬

 at this time. 

4. Loosen the screw 

⑭

 and move 

the needle bar 

⑫

 up and down to 

adjust the height. 
5. Tighten the Screw 

⑭

. 

6. Turn the machine pulley and 

check that the needle goes into the 

middle of the needle hole in the feed 

fog.

 

 

 

 

 

 

www.garudan.cz

Summary of Contents for GARUDAN GF-2207-147






















































Reviews:

No comments