manualshive.com logo in svg

Anita GARUDAN GF-2207-147, User Manual, Page: 27 / 53

Share
Download
Anita GARUDAN GF-2207-147 User Manual Download Page 27

© ANITA  

MP03700EN_181101 

 

27 

 

9. STANDARD ADJUSTMENTS 

 

Adjusting of the feed dog height: 

 

 

 

 

 

 

 

 

1. Turn the pulley until the feed dog 

①

 rises to the highest position. 

2. Tilt back the machine head. 
3. Loosen Screw 

②

 and raise or 

lower the feed dog holder 

③

 so that 

the feed dog 

①

 will raise to about 

1.0mm above the needle plate. 
4. Tighten the screw 

④

. 

 

 

 

 

 
 

 

Adjusting the presser foot height: 

 

 

 

1. Loosen the nut 

①

 and then loosen 

the presser foot adjustment screw 

②

. 

2. Open the face plate. 
3. Raise the presser foot 

④

 with the 

presser foot lifter 

⑦

. 

4. Loosen the screw 

⑤

 and then move 

the needle bar up hoe down to adjust 
so that the presser foot 

④

 is 

approximately 7mm above the top of 

the needle plate. Note: Be careful not 
to rotate the needle bar 

⑥

. 

5. Tighten the screw 

⑤

. 

6. Adjust the presser foot pressure by 

turning the presser foot adjustment 
screw 

②

, and then tighten the nut 

①

. 

(Refer to page 24) 

 

 

www.garudan.cz

Summary of Contents for GARUDAN GF-2207-147






















































Reviews:

No comments