manualshive.com logo in svg

Analog Devices ADuCM355, Hardware Reference Manual

The Analog Devices ADuCM355 is a cutting-edge microcontroller for precision measurement and data acquisition applications. Unlock the full potential of this advanced device by downloading the comprehensive Hardware Reference Manual for free at manualshive.com. The manual provides essential insights and technical details to help you harness the power of ADuCM355.

Share
Download
background image

ADuCM355

 Hardware Reference Manual 

UG-1262

 

Rev. B | Page 205 of 312 

SRAM 

This section provides an overview of the SRAM functionality of the 

ADuCM355

 processor. For details about the SRAM_INITSTAT, 

SRAM_CTL, and SRAMRET registers, refer to the Register Summary: Power Management Unit section. 

This memory space contains the application instructions and constant data that must be executed in real time. It supports read and write access 
via the Cortex-M3 core and read and write DMA access by system peripherals. SRAM is divided into data SRAM of 32 kB and instruction 
SRAM of 32 kB. If instruction SRAM is not enabled, the associated 32 kB can be mapped as data SRAM, resulting in a 64 kB data SRAM. 

166

75-

037

MODE 2

CACHE OFF

0kB INSTRUCTION

SRAM

64kB DATA SRAM

256kB FLASH

8kB DATA SRAM

8kB DATA SRAM

16kB DATA SRAM

16kB DATA SRAM

12kB DATA SRAM

4kB DATA SRAM

MODE 1

4kB CACHE

28kB INSTRUCTION

SRAM

32kB DATA SRAM

256kB FLASH

8kB DATA SRAM

8kB DATA SRAM

16kB INSTRUCTION

SRAM

12kB INSTRUCTION

SRAM

16kB DATA SRAM

MODE 0

CACHE OFF

32kB INSTRUCTION

SRAM

32kB DATA SRAM

256kB FLASH

12kB DATA SRAM

12kB INSTRUCTION

SRAM

8kB DATA SRAM

16kB INSTRUCTION

SRAM

12kB INSTRUCTION

SRAM

16kB DATA SRAM

MODE 3

4kB CACHE

0kB INSTRUCTION

SRAM

60kB DATA SRAM

256kB FLASH

8kB DATA SRAM

8kB DATA SRAM

16kB DATA SRAM

16kB DATA SRAM

12kB DATA SRAM

INITIALIZATION

ADDRESS

END

ADDRESS

0x0000 0000

0x0003 FFFF

0x1000 0000

0x1000 0FFF

0x1000 1000

0x1000 1FFF

0x1000 2000

0x1000 2FFF

0x1000 3000

0x1000 3FFF

0x1000 4000

0x1000 4FFF

0x1000 5000

0x1000 5FFF

0x1000 6000

0x1000 6FFF

0x1000 7000

0x1000 7FFF

0x2000 0000

0x2000 0FFF

0x2000 1000

0x2000 1FFF

0x2000 2000

0x2000 2FFF

0x2000 3000

0x2000 3FFF

0x2000 4000

0x2000 4FFF

0x2000 5000

0x2000 5FFF

0x2000 6000

0x2000 6FFF

0x2000 7000

0x2000 7FFF

0x2004 0000

0x2004 0FFF

0x2004 1000

0x2004 1FFF

0x2004 2000

0x2004 2FFF

0x2004 3000

0x2004 3FFF

0x2004 4000

0x2004 4FFF

0x2004 5000

0x2004 5FFF

0x2004 6000

0x2004 6FFF

0x2004 7000

NOT MAPPED
ALWAYS RETAINED
NOT RETAINED
RETAINED DURING HIBERNATE IF PROGRAMMED BY USER

0x2004 7FFF

 

Figure 54. 

ADuCM355

 SRAM Memory Details 

SRAM FEATURES 

The SRAM used by the 

ADuCM355

 processor supports the following features: 

 

Low power controller for data SRAM, instruction SRAM, and cache SRAM. 

 

Total available memory: 64 kB. 

 

Maximum retained memory in hibernate mode: 32 kB. 

 

The data SRAM is composed of 32 kB. There is an option to retain 8 kB or 16 kB in hibernate mode. 

 

The instruction SRAM is composed of 32 kB. There is an option to retain 16 kB in hibernate mode. 

 

If instruction SRAM is not enabled, the associated 32 kB can be mapped as data SRAM. In this case, there is the option to retain 
8 kB, 16 kB, 24 kB, or 32 kB of data SRAM. 

Summary of Contents for ADuCM355

























































































































































































































































































































Reviews:

No comments

Related manuals for ADuCM355

Balboa Instruments EL Series Hot Sheet preview
EL Series
Brand: Balboa Instruments Pages: 10
Federal Signal Corporation FC Description, Specifications, Installation, Operation, And Service Manual preview
FC
Brand: Federal Signal Corporation Pages: 34
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Vageo DT-1 Manual preview
DT-1
Brand: Vageo Pages: 2
Kampmann 197901960988 Manual preview
197901960988
Brand: Kampmann Pages: 5
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Brand: Mold-Masters Pages: 2
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Brand: Trinamic Pages: 30
EBS CPX200NB Installation And Programming Manual preview
CPX200NB
Brand: EBS Pages: 116
Daikin BRC1H62W Operation Handbook preview
BRC1H62W
Brand: Daikin Pages: 2
Leviton GreenMax DRC DRC07-ED0 Quick Start Manual preview
GreenMax DRC DRC07-ED0
Brand: Leviton Pages: 2
Meilhaus Electronic USB-GT Manual preview
USB-GT
Brand: Meilhaus Electronic Pages: 19
Gardenic GN-1113 User Manual preview
GN-1113
Brand: Gardenic Pages: 14
Galcon DC-11SF Installation And Operating Instructions Manual preview
DC-11SF
Brand: Galcon Pages: 24
NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Quick Start Manual preview
freescale Kinetics TWR-K60N512-KEIL
Brand: NXP Semiconductors Pages: 5
Bettis GVO-C Series Operation And Maintenance Manual preview
GVO-C Series
Brand: Bettis Pages: 14
Hubbell Electric Fire Pump Controllers LXi-2400 Specifications preview
Electric Fire Pump Controllers LXi-2400
Brand: Hubbell Pages: 2
Digital View DD-1920-DUAL-DVI Instructions Manual preview
DD-1920-DUAL-DVI
Brand: Digital View Pages: 30

Brands by name

Popular brands

Load more brands