manualshive.com logo in svg

Analog Devices ADuCM355, Hardware Reference Manual

The Analog Devices ADuCM355 is a cutting-edge microcontroller for precision measurement and data acquisition applications. Unlock the full potential of this advanced device by downloading the comprehensive Hardware Reference Manual for free at manualshive.com. The manual provides essential insights and technical details to help you harness the power of ADuCM355.

Share
Download
background image

ADuCM355

 Hardware Reference Manual 

UG-1262

 

Rev. B | Page 251 of 312 

Bits Bit 

Name  Settings Description 

Reset Access 

3 

CPOL 

 

Serial Clock Polarity. 

0x0 

R/W 

 

 

0 

Serial clock idles low. 

 

 

 

 

1 

Serial clock idles high. 

 

 

2 CPHA 

 

Serial 

Clock Phase Mode. 

0x0 

R/W 

 

 

0 

Serial clock pulses at the end of each serial bit transfer.  

 

 

 

 

1 

Serial clock pulses at the beginning of each serial bit transfer. 

 

 

1 

MASEN 

 

Master Mode Enable. 

0x0 

R/W 

 

 

0 

Enable slave mode. 

 

 

 

 

1 

Enable master mode. 

 

 

0 SPIEN 

 

SPI 

Enable. 

0x0 R/W 

 

 

0 

Disable the SPI. 

 

 

 

 

1 

Enable the SPI. 

 

 

 

INTERRUPT CONFIGURATION REGISTERS 

Address: 0x40004014, Reset: 0x0000, Name: SPI0_IEN 

Address: 0x40024014, Reset: 0x0000, Name: SPI1_IEN 

Table 311. Bit Descriptions for SPI0_IEN, SPI1_IEN 

Bits Bit 

Name Settings Description 

Reset Access 

15 Reserved 

 

Reserved. 

0x0 R 

14 TXEMPTY 

 

Transmit FIFO Empty Interrupt Enable. This bit enables the SPIx_STAT, Bit 2 interrupt 
whenever the transmit FIFO is emptied. 

0x0 R/W 

 

 

0 

TXEMPTY interrupt is disabled. 

 

 

 

 

1 

TXEMPTY interrupt is enabled. 

 

 

13 

XFRDONE 

 

SPI Transfer Completion Interrupt Enable. This bit enables the SPIx_STAT, Bit 1 interrupt. 

0x0 

R/W 

 

 

0 

XFRDONE interrupt is disabled. 

 

 

 

 

1 

XFRDONE interrupt is enabled. 

 

 

12 TXDONE 

 

SPI Transmit Done Interrupt Enable. This bit enables the SPIx_STAT, Bit 3 interrupt in read 
command mode. This interrupt can be used to signal the change of SPI transfer direction 
in read command mode. 

0x0 R/W 

 

 

0 

TXDONE interrupt is disabled. 

 

 

 

 

1 

TXDONE interrupt is enabled. 

 

 

11 RDY 

 

Ready Signal Edge Interrupt Enable. This bit enables the SPIx_STAT, Bit 15 interrupt 
whenever an active edge occurs on P0.3 signals. If SPIx_FLOW_CTL, Bits[1:0] = 0b10, this 
bit is set whenever an active edge is detected on the P0.3 signal. If SPIx_FLOW_CTL, 
Bits[1:0] = 0b11, this bit is set if an active edge is detected on the MISO signal. If 
SPIx_FLOW_CTL, Bits[1:0] = 0b00 or 0b01, this bit is always 0. The active edge (rising or 
falling) is determined by SPIx_FLOW_CTL, Bit 4.  

0x0 R/W 

 

 

0 

Ready signal edge interrupt is disabled. 

 

 

 

 

1 

Ready signal edge interrupt is enabled. 

 

 

10 

RXOVR 

 

Receive Overflow Interrupt Enable. 

0x0 

R/W 

 

 

0 

Receive overflow interrupt is disabled. 

 

 

 

 

1 

Receive overflow interrupt is enabled. 

 

 

9 TXUNDR 

 

Transmit 

Underflow Interrupt Enable. 

0x0 

R/W 

 

 

0 

Transmit underflow interrupt is disabled. 

 

 

 

 

1 

Transmit underflow interrupt is enabled. 

 

 

8 

CS 

 

Enable Interrupt on Every Chip Select Edge in Slave Continuous Mode.  

0x0 

R/W 

 

 

0 

No interrupt is generated and the status bits are not asserted. 

 

 

  

1 

If the SPI module is configured as a slave in continuous mode, any edge on chip select 
generates an interrupt and the corresponding status bits (SPIx_STAT, Bit 14 and 
SPIx_STAT, Bit 13) are asserted. This bit has no effect if the SPI is not in continuous mode 
or if it is a master. 

 

 

[7:3] Reserved 

 Reserved. 

0x0 R 

Summary of Contents for ADuCM355

























































































































































































































































































































Reviews:

No comments

Related manuals for ADuCM355

Oldham MX15 Installation And Operating Manual preview
MX15
Brand: Oldham Pages: 32
HANYOUNG NUX TS500 Manual preview
TS500
Brand: HANYOUNG NUX Pages: 56
Vacon 100X series Installation, Technical And Maintenance Manual preview
100X series
Brand: Vacon Pages: 132
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Brand: fadini Pages: 28
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Brand: Ros Pages: 10
AirCycler SmartExhaust Manual preview
SmartExhaust
Brand: AirCycler Pages: 2
TS Performance Torque Converter Lock-Up Manual preview
Torque Converter Lock-Up
Brand: TS Performance Pages: 4
National Instruments MXI-Express Gen-3 x16 User Manual preview
MXI-Express Gen-3 x16
Brand: National Instruments Pages: 38
E-T-A EtherNetIP ControlPlex CPC12EN Quick Start Manual preview
EtherNetIP ControlPlex CPC12EN
Brand: E-T-A Pages: 7
zeeltronic PDCI-NS1V User Manual preview
PDCI-NS1V
Brand: zeeltronic Pages: 15
M-system M8BS2-081 Instruction Manual preview
M8BS2-081
Brand: M-system Pages: 3
Guangdong Schen Investment RC-M2 User Manual preview
RC-M2
Brand: Guangdong Schen Investment Pages: 15
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Brand: KEPCO Pages: 34
Rain Bird AESPLX16SM Installation, Connection And Settings preview
AESPLX16SM
Brand: Rain Bird Pages: 20
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Brand: SUPMEA Pages: 32
Yaesu G-5500DC Instruction Manual preview
G-5500DC
Brand: Yaesu Pages: 12
Danfoss AME 85 QM Operating Manual preview
AME 85 QM
Brand: Danfoss Pages: 16
NTI AG LinMot E1200 Series Installation Manual preview
LinMot E1200 Series
Brand: NTI AG Pages: 20

Brands by name

Popular brands

Load more brands