Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 199

Page: 199 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

199

3. Use the twist tie that comes with the power supply to secure the cord to

an anchor on the chassis, as shown in Figure 120.

Figure 120. Securing the Power Cord for the AT-SBxPWRPOE1 Power

Supply to an Anchor

4. Connect the power cord to an appropriate AC power source to power

on the power supply.

5. If the chassis has two AT-SBxPWRPOE1 Power Supplies, repeat this

procedure to power on the second power supply.

Figure 121 on page 200 is an illustration of the power cords for a
chassis with four power supplies.

Anchor

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands