Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 176

Page: 176 / 356

Chapter 8: Cabling the Ethernet Line Cards

176

Section II: Installing the Chassis

5. Connect the fiber optic cable to the port on the transceiver, as shown

in Figure 103 on page 176. The connector should snap into the port.

Figure 103. Attaching a Fiber Optic Cable to a Transceiver in the AT-

SBx81XS16 Line Card

6. Repeat this procedure to install additional SFP or SFP+ transceivers in

the line cards.

7. After installing and cabling the transceivers, do one of the following:



To install and cable additional transceivers in the Ethernet line
cards, go to the appropriate section in this chapter for instructions.



To cable the ports on the controller card, go to Chapter 9, “Cabling
the AT-SBx81CFC960 Controller Fabric Card” on page 183.



After cabling all the ports in the chassis, go to Chapter 10,
“Powering On the Chassis” on page 193.

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands