Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 259

Page: 259 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

259

Figure 158. Removing the Power Supply from the Chassis

4. Do one of the following:



To install a new power supply, refer to Chapter 6, “Installing the
Power Supplies” on page 123.



If you are not installing a new power supply, continue with the rest
of this procedure to install a blank slot cover.

5. Place the locking handle on the slot cover in the up position and slide

the cover into the empty power supply slot. Refer to Figure 159 on
page 260.

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands