Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 205

Page: 205 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

205

Figure 127. Installing the Grounding Wire

5. Connect the other end of the grounding wire to the building protective

earth.

Warning

When installing this equipment, always ensure that the power supply
ground connection is installed first and disconnected last.



E11

Note

This system will work with a positive grounded or negative grounded
DC system.



E13

After connecting the grounding wire, go to “Choosing a Method for
Attaching the Power Wires” on page 208.

Grounding
wire

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands