Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 287

Page: 287 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

287

4. Slowly pull the module out 25 mm (1 in.). Refer to Figure 182.

Figure 182. Withdrawing the AT-SBxFAN06 Fan Module 25 mm (1 in.)

from the Chassis

5. Wait ten seconds for the fans to stop.

Warning

The fan module has hazardous moving parts. Keep fingers away
from moving fan blades.

6. After the fans have stopped, slide the module from the chassis. Refer

to Figure 183 on page 288.

25 mm
(1 in.)

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands