Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 350

Page: 350 / 356

Appendix A: Technical Specifications

350

PoE Mode

IEEE 802.3af Class 1 (4.0 W /port)

96 ports Maximum

Table 47. Available Power Over Ethernet with Two PoE Power Supplies

Two PoE Power Supply Installed

2400 W @ 56 VDC

IEEE 802.3at Class 4 (30 W /port)

80 ports Maximum

IEEE 802.3af Class 3 (15.4 W /port) 96 ports Maximum

IEEE 802.3af Class 2 (7.3 W /port)

96 ports Maximum

IEEE 802.3af Class 1 (4.0 W /port)

96 ports Maximum

Table 48. PoE Mode on the AT-SBx81GP24 PoE Line Card

IEEE 802.3af / IEEE 802.3at:

Alternative Mode A

Table 46. Available Power Over Ethernet with One PoE Power Supply

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands