Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 128

Page: 128 / 356

Chapter 6: Installing the Power Supplies

128

Section II: Installing the Chassis

4. Move the locking handle on the power supply to the unlocked or up

position. See Figure 54 on page 128.

Figure 54. Unlocking the Handle on the Power Supply

5. Align and insert the power supply into the power supply slot. Figure 55

shows the power supply installed in slot D.

Figure 55. Inserting the AT-SBxPWRSYS1 or AT-SBxPWRSYS2 AC

System Power Supply

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands