Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 154

Page: 154 / 356

Chapter 7: Installing the AT-SBx81CFC960 Controller and Ethernet Line Cards

154

Section II: Installing the Chassis

Figure 80. Removing the Blank Slot Cover from the AT-SBx81XLEM Line

Card

6. With your thumb and forefinger, pull out the retaining pin on the side of

the line card and turn it clockwise one quarter turn so that it remains in
the retracted position. Refer to Figure 81 on page 155.

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands