Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 219 | Manualshive

Page: 219 / 356

background image

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

219

Figure 144. Removing the Terminal Screws

6. With a #3 Phillips-head screwdriver, connect the positive (+) power

lead wire to the positive terminal on the power supply, with one of the
terminal screws removed in the previous step. The positive terminal is
on the left. Refer to Figure 145 on page 220.

Allied Telesis recommends tightening the screw to 30 to 40 inch-lbs.

«
...
217
218
219
220
221
...
»

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-SB*81CFC960

Verizon DSL-2750B

Brand: D-Link Pages: 6

Brand: D-Link Pages: 10

Brand: D-Link Pages: 38

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: D-Link Pages: 213

Brand: Conceptronic Pages: 2

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

Brand: Macsense Pages: 39

Brand: Paradyne Pages: 23

Vigor 2760 Series

Brand: Draytek Pages: 54

Brand: Keithley Pages: 98

Brand: ICP DAS USA Pages: 62

Brand: INNOSILICON Pages: 11

Brand: FOR-A Pages: 37

Brand: ActiveEye Pages: 35

Brand: Tripp Lite Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands