Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 127

Page: 127 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

127

3. Remove the new power supply from the shipping package and verify

the package contents, listed in Figure 53 on page 127.

If any item is missing or damaged, contact your Allied Telesis sales
representative for assistance.

Figure 53. Items Included with the AT-SBxPWRSYS1 or AT-

SBxPWRSYS2 AC System Power Supply

Note

Store the packaging material in a safe location. You must use the
original shipping material if you need to return the unit to Allied
Telesis.

Note

The tie wrap is used to secure the power cord to the chassis in
“Powering On the AT-SBxPWRSYS1 or AT-SBxPWRSYS2 AC
System Power Supply” on page 195.

One AT-SBxPWRSYS1 or
AT-SBxPWRSYS2 Power
Supply

One regional AC power cord

One tie wrap

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands