manualshive.com logo in svg

Allied Telesis AT-SB*81CFC960, Installation Manual

The Allied Telesis AT-SB*81CFC960 is a high-performance switch with advanced features. Maximize its potential by downloading the free Installation Manual from our website. This comprehensive manual provides step-by-step instructions for easy setup and configuration. Get the most out of your product with our user-friendly manual.manualshive.com

Share
Download
background image

Contents

6

Duplex Mode ............................................................................................................................................. 64
Maximum Distance .................................................................................................................................... 65
Cable Requirements.................................................................................................................................. 65
Automatic MDIX Detection ........................................................................................................................ 67
Port Pinouts ............................................................................................................................................... 67

Power over Ethernet on the AT-SBx81GP24 Line Card .................................................................................. 68

Powered Device Classes........................................................................................................................... 68
Power Budgeting ....................................................................................................................................... 69
PoE Wiring................................................................................................................................................. 69

Chapter 3: AT-SBx81CFC960 Controller Fabric Card ................................................................................ 71

Controller Fabric Cards for the AT-SBx8106 Chassis...................................................................................... 72
Hardware Components on the AT-SBx81CFC960 Card.................................................................................. 74
Guidelines ........................................................................................................................................................ 76
Dual Controller Cards ...................................................................................................................................... 78
SYS Status LEDs ............................................................................................................................................. 80
eco-friendly Button ........................................................................................................................................... 82
SBx Linecard Status LEDs............................................................................................................................... 83
SFP+ Slots ....................................................................................................................................................... 84
Console (RS-232) Port..................................................................................................................................... 86
Ethernet Management Port (NET MGMT) ....................................................................................................... 87

NET MGMT LED ....................................................................................................................................... 87

USB Port .......................................................................................................................................................... 89
Reset Button .................................................................................................................................................... 90
AlliedWare Plus Software Releases for the Hardware Components ............................................................... 92

Section II: Installing the Chassis ............................................................................. 95

Chapter 4: Safety Precautions and Site Requirements  ............................................................................. 97

Reviewing Safety Precautions ......................................................................................................................... 98
Selecting a Site for the SwitchBlade x8106 ................................................................................................... 102
Installation Tools and Material ....................................................................................................................... 104

Chapter 5: Installing the Chassis in an Equipment Rack ........................................................................ 105

Required Tools and Material .......................................................................................................................... 106
Preparing the Equipment Rack ...................................................................................................................... 107
Unpacking the AT-SBx8106 Chassis ............................................................................................................. 110
Removing the Rubber Feet ............................................................................................................................ 112
Adjusting the Equipment Rack Brackets ........................................................................................................ 114
Installing the Chassis in the Equipment Rack ................................................................................................ 116
Removing the Shipping Brace ....................................................................................................................... 120
Installing the Chassis Grounding Wire ........................................................................................................... 121

Chapter 6: Installing the Power Supplies  ................................................................................................. 123

Protecting Against Electrostatic Discharge (ESD) ......................................................................................... 124
Installing AT-SBxPWRSYS1 or AT-SBxPWRSYS2 AC System Power Supplies.......................................... 125
Installing AT-SBxPWRPOE1 PoE Power Supplies........................................................................................ 131
Installing AT-SBxPWRSYS1 DC System Power Supplies............................................................................. 136

Chapter 7: Installing the AT-SBx81CFC960 Controller and Ethernet Line Cards  ................................. 143

Guidelines to Handling the Controller and Line Cards ................................................................................... 144
Installing the AT-SBx81CFC960 Controller Fabric Card................................................................................ 146
Installing Expansion Modules in AT-SBx81XLEM Ethernet Line Cards......................................................... 152
Installing the Ethernet Line Cards .................................................................................................................. 160
Installing the Blank Slot Covers ..................................................................................................................... 164

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-SB*81CFC960

4RF Aprisa LTE Quick Start Manual preview
Aprisa LTE
Brand: 4RF Pages: 7
Eaton Power Xpert Meter 2000 Instructions Manual preview
Power Xpert Meter 2000
Brand: Eaton Pages: 16
Eaton POW-R-COMMAND 1000 User Manual preview
POW-R-COMMAND 1000
Brand: Eaton Pages: 84
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
Niveo NWAR33P User Manual preview
NWAR33P
Brand: Niveo Pages: 155
Premio FlacheSAN1L-D4 Quick Manual preview
FlacheSAN1L-D4
Brand: Premio Pages: 3
TP-Link TD-8817 User Manual preview
TD-8817
Brand: TP-Link Pages: 73
NetBurner MOD5272 Quick Start Manual preview
MOD5272
Brand: NetBurner Pages: 15
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
Draytek Vigor 2700G Specifications preview
Vigor 2700G
Brand: Draytek Pages: 2
Genie IP8ESP User Manual preview
IP8ESP
Brand: Genie Pages: 6
3Com EtherLink 3C905C-TX User Manual preview
EtherLink 3C905C-TX
Brand: 3Com Pages: 96
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140
KYLAND Technology KIEN1009 Hardware Installation Manual preview
KIEN1009
Brand: KYLAND Technology Pages: 24
Cyclades AlterPath Manager 2500 Installation, Configuration And User Manual preview
AlterPath Manager 2500
Brand: Cyclades Pages: 368

Brands by name

Popular brands

Load more brands