Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 43

Page: 43 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section I: Hardware Overview

Table 8. Port LEDs on the AT-SBx81GT40 Line Card

LED

State

Description

L/A

Solid Green

The port has established an 1000 Mbps link
to a network device.

Flashing
Green

The port is transmitting or receiving data at
1000 Mbps.

Solid Amber

The port has established a 10 or 100 Mbps
link to a network device.

Flashing
Amber

The port is transmitting or receiving data at
10 or 100.

Off

The port has not established a link with
another network device or the LEDs are
turned off. To turn on the LEDs, use the
eco-friendly button.

Right LED

This LED is not used.

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands