Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 197

Page: 197 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

197

Figure 118. Securing the Power Cord for the AT-SBxPWRSYS1 or AT-

SBxPWRSYS2 AC System Power Supply to an Anchor

4. Connect the power cord to an appropriate AC power source to power

on the power supply.

5. If the chassis has two AT-SBxPWRSYS1 or AT-SBxPWRSYS2 AC

System Power Supplies, repeat this procedure to power on the second
power supply.

After powering on the AC system power supplies, do one of the follow:



If the chassis has AT-SBxPWRPOE1 PoE Power Supplies,
perform the procedure in “Powering On AT-SBxPWRPOE1 Power
Supplies” on page 198.



Otherwise, go to “Monitoring the Initialization Process” on
page 227.

Anchor

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands