Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 151

Page: 151 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

151

Figure 77. Tightening the Thumb Screws on the AT-SBx81CFC960 Card

10. Tighten the screws with a #2 Phillips-head screwdriver to secure the

controller card to the chassis.

Allied Telesis recommends tightening the screws to 5 inch-lbs.

11. if the chassis is to have two AT-SBx81CFC960 Controller Fabric

Cards, repeat this procedure to install the second card.

12. After installing the controller cards, do one of the following:



If you purchased AT-SBx81XLEM Line Cards with expansion
modules, go to “Installing Expansion Modules in AT-SBx81XLEM
Ethernet Line Cards” on page 152.



Otherwise, go to “Installing the Ethernet Line Cards” on page 160.

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands