Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 190 | Manualshive

Page: 190 / 356

background image

Chapter 9: Cabling the AT-SBx81CFC960 Controller Fabric Card

190

Section II: Installing the Chassis

Figure 114. Attaching a Fiber Optic Cable to an SFP+ Transceiver in the

AT-SBx81CFC960 Controller Fabric Card

7. Repeat this procedure to install additional SFP+ transceivers in the

AT-SBx81CFC960 Controller Fabric Card.

8. If you are not building a stack with the VCStack Plus feature, do one of

the following:



To install and cable additional transceivers in the chassis, go to the
appropriate section in this chapter for instructions.



After cabling all the ports in the chassis, go to Chapter 10,
“Powering On the Chassis” on page 193.

9. If you are building a stack with the VCStack Plus feature, do the

following:



Double-check the wiring of the cables of the trunk between the
SFP+ slots of the controller cards of the two chassis to be sure
they are connected correctly. The possible wiring configurations
are given in “Cabling Configurations for the Trunk” on page 305.



Afterwards, go to “Powering On the Stack” on page 333.

«
...
188
189
190
191
192
...
»

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-SB*81CFC960

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 2

COMSPHERE 6800 Series

Brand: Paradyne Pages: 155

COMSPHERE 6800 Series

Brand: Paradyne Pages: 44

Brand: Zonet Pages: 8

Brand: REXROTH Pages: 68

Brand: Vonets Pages: 8

APS6-400 Series

Brand: Eaton Pages: 114

Brand: H3C Pages: 12

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

2000 IDU Series

Brand: EMS Pages: 52

Brand: Ozenda Pages: 116

Sinus 154 data II

Brand: T-COM Pages: 12

OptiBond 210 C Series

Brand: i-MO Pages: 16

Brand: F.F. Group Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands