Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 305 | Manualshive

Page: 305 / 356

background image

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section III: Building a Stack with VCStack Plus

305

Cabling Configurations for the Trunk

This section illustrates the cabling configurations for the transceivers of the
trunk.

One Controller

Card Per Chassis

Figure 187 illustrates the correct wiring configuration for the fiber optic
wires for the stacking transceivers when each chassis has only one AT-
SBx81CFC960 Controller Fabric Card. The transceiver in SFP+ slot 1 in
one controller card is connected to the transceiver in SFP+ slot 1 in the
card in the other chassis, the transceiver in SFP+ slot 2 is connected to the
transceiver in SFP+ slot 2 in the other chassis, and so on.

Figure 187. Cabling the SFP+ Slots When Both Switches have One

Controller Card

Please note the following:



The trunk has a maximum bandwidth of 40Gbps when each
chassis has one controller card and the trunk has four links.



The switches will form the stack even if the transceivers are cabled
incorrectly such that the wires between transceivers crossover
(e.g., the transceiver in SFP+ slots 1 is connected to the
transceiver in SFP+ slot 2). However, the bandwidth of the trunk is
reduced.

«
...
303
304
305
306
307
...
»

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-SB*81CFC960

Network Card-MS

Brand: Eaton Pages: 89

Brand: Observint Pages: 11

Brand: TRENDnet Pages: 2

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: TP-Link Pages: 110

Hotwire ATM Line Cards 8335

Brand: Paradyne Pages: 132

JetNet 3508-LVDC

Brand: Korenix Pages: 16

Brand: Aaeon Pages: 57

Brand: Juniper Pages: 196

Network Adapter ADZIFCF

Brand: Addonics Technologies Pages: 1

Brand: Juniper Pages: 396

Brand: Planet Pages: 13

Brand: Quantum Pages: 108

Brand: DayTronic Pages: 13

Brand: Trend Micro Pages: 2

Brand: Linksys Pages: 44

Brand: TCL Pages: 38

Brand: TCL Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands