Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 98 | Manualshive

Page: 98 / 356

background image

Chapter 4: Safety Precautions and Site Requirements

98

Section II: Installing the Chassis

Reviewing Safety Precautions

Please review the following safety precautions before you begin to install
the switch.

Note

The



indicates that a translation of the safety statement is

available for viewing in portable document format (PDF) titled

Translated Safety Statements

from our web site at

www.alliedtelesis.com/support

.

Warning

Class 1 Laser product.



L1

Warning

Do not stare into the laser beam.



L2

Warning

To prevent electric shock, do not remove the cover. No user-
serviceable parts inside. This unit contains hazardous voltages and
should only be opened by a trained and qualified technician. To
avoid the possibility of electric shock, disconnect electric power to
the product before connecting or disconnecting the LAN cables.



E1

Warning

Do not work on equipment or cables during periods of lightning
activity.



E2

Warning

Power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord.



E3

Warning

Class I Equipment. This equipment must be earthed. The power
plug must be connected to a properly wired earth ground socket
outlet. An improperly wired socket outlet could place hazardous
voltages on accessible metal parts.



E4

«
...
96
97
98
99
100
...
»

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-SB*81CFC960

Brand: Linksys Pages: 2

Brand: X-Micro Pages: 74

Brand: TP-Link Pages: 2

Brand: E-Lins Pages: 113

Brand: Ubiquiti Pages: 20

Brand: AMG Systems Pages: 2

Brand: B&B Electronics Pages: 2

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: M86 Security Pages: 309

Brand: Kohler Pages: 32

18x18 Card Cage

Brand: WolfPack Pages: 31

Brand: ZoneVu Pages: 15

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brand: H3C Pages: 4

GigaSpire BLAST u6

Brand: Calix Pages: 9

Cradlepoint AER1600

Brand: Choose 2 rent Pages: 5

Router 3000 Series

Brand: 3Com Pages: 37

Brand: TP-Link Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands