ALLIANCE ST3LXFSP401NW22 Programming Manual Download Page 44

Page: 44 / 102

Programming Control

802953

How to Program Breakaway Step Speed
“brAy”

This option allows the owner to set the breakaway

speed.

1. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad to scroll through the

programmable Cycle Programming options until

“

brAy

” appears in the display.

2. When “

brAy

” appears in the display, press the

START (enter) keypad. The current Breakaway

Step Speed will appear in the display.

“

rEg

” = Regular agitate speed (factory default

setting for NORMAL 90, NORMAL

60, NORMAL 40, PERM PRESS 60)

“

” = Low agitate speed (factory default

setting for DELICATES 30,

DELICATES COLD)

3. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad to change the current status.

4. Press the START (enter) keypad when the

desired status appears in the display. The next

Cycle Programming option, “

StA1

”, will appear

in the display.

NOTE: To program another cycle, repeat Cycle

Programming steps. To program other options,

press the DELICATES 30 (<) keypad and refer to

the appropriate section.

How to Exit Programming Feature

Press the DELICATES 30 (<) keypad until the control

returns to Ready Mode.

Summary of Contents for ST3LXFSP401NW22







































































































Search results

Summary of Contents for ST3LXFSP401NW22

Reviews:

Related manuals for ST3LXFSP401NW22

Brands by name

Popular brands

ALLIANCE ST3LXFSP401NW22, Programming Manual

Search results

Summary of Contents for ST3LXFSP401NW22

Reviews:

Related manuals for ST3LXFSP401NW22

Brands by name

Popular brands