manualshive.com logo in svg

Allen-Bradley Kinetix 5500, Reference Manual, Page: 362 / 497

Share
Download
Allen-Bradley Kinetix 5500 Reference Manual Download Page 362

Chapter 4 

CIP Axis Attributes 

 

362

 

Rockwell Automation Publication MOTION-RM003I-EN-P - February 2018 

Homing Sequence Types 

Description 

Active Unidirectional Home to 

Switch then Marker 

This active homing sequence is useful for multi-turn rotary applications when 

unidirectional motion is required. 
When this sequence is performed in the Active Homing Mode, the axis moves in the 

specified Home Direction at the specified Home Speed and Home Acceleration until the 

home switch is detected. The axis continues in the same direction at the Home Speed 

until the first marker event is detected. If the Home Offset is zero, the Home Position is 

assigned to the axis position at the precise position where the marker was detected, 

and the axis decelerates to a stop at the specified Home Deceleration. The axis position 

is updated based on the Home Position and Home Offset. 
If Home Offset is non-zero, then the Home Position will be offset from the point where 

the marker was detected by this value. The controller then continues to move the axis 

to the Home Position at the specified Home Speed and Home Acceleration using a 

trapezoidal move profile. 
By setting a Home Offset greater than the deceleration distance, unidirectional motion 

to the Home Position is insured. However, if the Home Offset value is less than the 

deceleration distance, then the axis is simply decelerated to a stop at the specified 

Home Deceleration. The axis does 

not

 reverse direction to move to the Home Position. 

In this case, the PC-bit leg of the associated MAH instruction is not set when the IP-bit 

leg is cleared. 
In the case where this homing sequence is performed on a cyclic axis and the Home 

Offset value is less than the deceleration distance when the home event is detected, the 

control automatically adds one or more revolutions to the move distance. This 

guarantees the resulting move to the Home Position is unidirectional. 
If the controller detects that the state of the home switch at the start of the homing 

sequence is active, the controller immediately establishes the Home Position based on 

the current axis position, and if allowed by the unidirectional motion constraint, begins 

to move to the Home Position.   

Summary of Contents for Kinetix 5500


















































































































































































































































































































































































































































































































Reviews:

No comments