Aeon AT56-69E Service Manual Download Page 148

Page: 148 / 196

BRAKES

8-3

BRAKE SYSTEM SERVICE NOTES

Disc brake systems are lightweight, low maintenance, and

perform well in the conditions ATVs routinely encounter.

There are a few things to remember when replacing disc brake

pads or performing brake system service to ensure proper

system function and maximum pad service life.

◎

Optional pads are available to suit conditions in your area.

Select a pad to fit riding style and environment.

◎

Do not over-fill the master cylinder fluid reservoirs.

◎

Make sure the brake levers return freely and completely.

◎

Check and adjust master cylinder reservoir fluid levels

after pad service.

◎

Make sure atmospheric vent on reservoirs are

unobstructed.

◎

Test for brake drag after any brake system service and

investigate cause if brake drag is evident.

◎

Make sure caliper moves freely on guide pins.

◎

Inspect caliper piston seals for foreign material that could

prevent caliper pistons from returning freely.

◎

Perform a brake burnishing procedure after installing new

pads to maximize service life.

Use only DOT 4 brake fluid as an assembly aid for all

procedures described in this chapter to prevent

brake system contamination.

DO NOT USE LUBRICANTS OF ANY KIND FOR

ASSEMBLY.

DISC BRAKE NOISE TROUBLESHOOTING

Dirt or dust buildup on the brake pads and disc is the most

common cause of brake noise (squeal caused by vibration). If

cleaning does not reduce the occurrence of brake noise, check

the backing of each pad for worn spots allowing

metal-to-metal contact. See table below.

BRAKE NOISE TROUBLESHOORTING

Possible Cause

Remedy

Dirt, dust, or imbedded material on pads or disc

Spray disc and pads with a non-flammable aerosol brake

cleaner only! Remove pads and/or disc hub to clean imbedded

material from disc or pads.

Pad(s) dragging on disc (noise or premature pad wear)

Improper adjustment

Insufficient lever or pedal clearance

Master cylinder reservoir overfilled

Master cylinder compensating port restricted

Master cylinder piston not returning completely

Caliper piston(s) not returning

Operator error (riding the brake / park brake applied)

Adjust pad stop.

Check position of controls & switches.

Set to proper level

Clean compensating port

Inspect. Repair as necessary

Clean piston(s) seal

Educate operator

Loose wheel hub or bearings

Check wheel and hub for abnormal movement.

Brake disc warped or excessively worn

Replace disc

Brake disc misaligned or loose

Inspect and repair as necessary

Noise is from other source (chain, axle, hub, disc or wheel)

If noise does not change when brake is applied check other

sources. Inspect and repair as necessary

Wrong pad for conditions

Change to a softer or harder pad

Summary of Contents for AT56-69E





































































































































































































Search results

Summary of Contents for AT56-69E

Reviews:

Aeon AT56-69E, Service Manual, Page: 148 / 196

Search results

Summary of Contents for AT56-69E

Reviews: