manualshive.com logo in svg

ABB IRB 2000, Product Manual

Share
Download
ABB IRB 2000 Product Manual Download Page 213

Def.range

0.00

 -

 0.45

 s

Default value

0.20

 s

Note

A restart attempt when it is not allowed will result in an error message:"NOT
ALLOWED COMMAND" at the programming unit.

5.2.4.23A
PATH (Motion optimizing)

It is possible to run the robot speed optimized or path optimized. The cycle time is normally

shorter with speed optimized than with path optimizing.

Note

Zone data under ZONE will be set to the default value if this parameter is
changed. Therefore remember to install the zone size again when the parameter
has been changed, if other values than the default value is required (see chapter
5.2.4.4).

Path optimizing will be installed if predefinition from PROM is used.

The system parameter for motion optimizing is installed as follows:

0 • Path optimized running
This is the default value when using predefinition from PROM. It is recommended to use
path optimized running, if nothing else is required. Normal corner zones will be installed
when path optimizing is installed. The motion will be stopped when changing from
ROBOT- toRECT-coordinates.

1 • Velocity optimized running

Velocity optimized running gives a smoother velocity at the cost of the path quality. The
robot will have the same path performance as old robots, without the SPF-function. Normal
zero zone will be installed when velocity optimizing is installed. The motion is not stopped

when changing from ROBOT- to RECT-ccordinates.

5.2.4.23B
CUR/ WIR (Arc welding software)

Description

Define CURRENT or WIRE SPEED to be used as welding parameters.

Menu

 CUR/WIR

Guide text

CUR (0)/ WIRE SPQ)

Def. range

0 = Current is used

1 = Wire speed is used

Default value

0, i.e. current

Note

If the parameter is changed, it is necessary to activate the system parameters

before changing the corresponding output, (CURRENT or WIRE SP), see 5.2.4.24.

INSTALLATION S3

5:49

Summary of Contents for IRB 2000















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands