ABB IRB 1400 Product Manual Download

Page: 41 / 198

2 Installation and commissioning

2.1.5 Stress Forces

3HAC021111-001 Revision: B

2.1.5 Stress Forces

Stiffness

The stiffness of the foundation must be designed to minimize the influence on the dynamic

behaviour of the robot.

TuneServo can be used for adapting the robot tuning to a non-optimal foundation.

IRB 1400 and IRB
1400H

Fxy and Mxy are vectors that can have any direction in the xy plane.

The Directions of the Stress Forces.

Force

Endurance load (in operation) Max. load (emergency stop)

Fxy

± 1500 N

± 2000 N

Fz (upright)

2800 ± 500 N

2800 ± 700 N

Fz (suspended)

-2800 ± 800 N

-2800 ± 1000 N

Torque

Endurance load (in operation) Max. load (emergency stop)

Mxy

± 1800 Nm

± 2000 Nm

± 400 Nm

± 500 Nm

Summary of Contents for IRB 1400







































































































































































































Search results

Summary of Contents for IRB 1400

Reviews:

Related manuals for IRB 1400

Brands by name

Popular brands

ABB IRB 1400, Product Manual

Search results

Summary of Contents for IRB 1400

Reviews:

Related manuals for IRB 1400

Brands by name

Popular brands