manualshive.com logo in svg

ABB IRB 1400, Product Manual

The ABB IRB 1400 is a versatile industrial robot that combines speed and precision. Enhance your understanding and maximize its potential by downloading the free product manual. Find step-by-step instructions, troubleshooting tips, and in-depth features exclusively at manualshive.com. Unlock endless possibilities with this comprehensive manual, at your fingertips.

Share
Download
background image

Table of Contents

3

0.0.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
0.0.2 Product documentation, M2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
0.0.3 Product documentation, M2004. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 11

1: Safety, service

13

1.0.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.1: General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1.1.1 Safety, service - General  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.1.2 Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1.3 Related information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.2: Safety risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.2.1 Safety risks related to gripper  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.2.2 Safety risks related to tools/workpieces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 18
1.2.3 Safety risks related to pneumatic/hydraulic systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.2.4 Safety risks during operational disturbances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.2.5 Safety risks during installation and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.2.6 Risks associated with live electric parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 22

1.3: Safety actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1.3.1 Safety fence dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.3.2 Fire extinguishing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.3.3 Emergency release of the manipulator's arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.3.4 Brake testing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.3.5 Risk of disabling function "Reduced speed 250 mm/s"  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.3.6 Safe use of the Teach Pendant Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 28
1.3.7 Work inside the manipulator's working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.3.8 Signal lamp (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2: Installation and commissioning

31

2.0.1 Transporting and Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.0.2 Stability / Risk of Tipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.0.3 System CD ROM and Diskette  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.0.4 Transport Locking Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2.1: On-site installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

2.1.1 Lifting the Manipulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.1.2 Turning the Manipulator (Inverted Suspension Application) . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.1.3 Assembling the robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.1.4 Suspended Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.1.5 Stress Forces  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.1.6 Amount of Space required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.1.7 Manually engaging the brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.1.8 Restricting the Working Space  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.1.9 Mounting Holes for Equipment on the Manipulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.1.10 Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

2.2: Customer connections on manipulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

2.2.1 Air supply and signals for extra equipment to upper arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.2.2 Connection of Extra Equipment to the Manipulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

3: Maintenance

51

3.0.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.0.2 Maintenance Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.1: Instructions for maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

3.1.1 Oil in gears 1-4  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
3.1.2 Greasing axes 5 and 6  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.1.3 Lubricating spring brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3.1.4 Changing the battery in the measuring system  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
3.1.5 Checking the mechanical stop, axis 1  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Summary of Contents for IRB 1400







































































































































































































Reviews:

No comments

Related manuals for IRB 1400

ABB SM1000 Replacing Instructions preview
SM1000
Brand: ABB Pages: 8
Yamaha Mark III User Manual preview
Mark III
Brand: Yamaha Pages: 83
Yamaha Mark III Operating Manual preview
Mark III
Brand: Yamaha Pages: 63
F.W. Bell 5200 Series Instruction Manual preview
5200 Series
Brand: F.W. Bell Pages: 75
Callaway 350TL Manual preview
350TL
Brand: Callaway Pages: 13
DAPAudio IEM-100 Beltpack User Manual preview
IEM-100 Beltpack
Brand: DAPAudio Pages: 19
Waterproof DRYSUIT Owner'S Manual preview
DRYSUIT
Brand: Waterproof Pages: 10
Ocean Optics USB2000 Installation And Operation Manual preview
USB2000
Brand: Ocean Optics Pages: 43
Ocean Technology Systems PDR-100 User Manual preview
PDR-100
Brand: Ocean Technology Systems Pages: 12
Ocean Reef GSM Mercury Instruction Manual preview
GSM Mercury
Brand: Ocean Reef Pages: 24
Lutron Electronics CT-2012 Operation Manual preview
CT-2012
Brand: Lutron Electronics Pages: 20
Rion VM-82A Concise Manual preview
VM-82A
Brand: Rion Pages: 4
AccuEnergy AcuMesh User Manual preview
AcuMesh
Brand: AccuEnergy Pages: 23
Nicols TWIN LASER GB II Instructions For Use Manual preview
TWIN LASER GB II
Brand: Nicols Pages: 22
KATA DGM-1500 Turva Manual preview
DGM-1500 Turva
Brand: KATA Pages: 20
Polhemus PATRIOT DB Installation Manual preview
PATRIOT DB
Brand: Polhemus Pages: 2
Xylem WTW Oxi 3205 Operating Manual preview
WTW Oxi 3205
Brand: Xylem Pages: 44
Eddyfi Technologies GEKKO M2M Technical Documentation Manual preview
GEKKO M2M
Brand: Eddyfi Technologies Pages: 31

Brands by name

Popular brands

Load more brands