Xerox WorkCentre 7300 Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 203

background image

25

Microsoft (NetBIOS over IP) Networks

Before You Start

1.

Print a

Configuration Report

as stated in the

Network Connectivity

section of this guide.

2.

Referring to the report,

verify that SMB is enabled

. To enable SMB at the Device, if required, follow

the procedure below.

3.

Referring to the Configuration Report,

verify that DNS

is

enabled

. The use of Naming Servers is

REQUIRED to resolve NetBIOS device names to IP addresses for packet routing over the TCP/IP
network.

4.

To enable the Device to communicate with the Naming Servers, refer to the instructions supplied in the
topic "TCP/IP Dynamic Addressing", located in the

NOS Selection

section of this guide.

5.

When using WINS or DNS, be sure to refer to your Server Operating System documentation for the
appropriate procedure to use to enable NetBIOS name to IP address resolution on the Server.

Enabling the SMB Setting at the Device, if required

1.

Press the

Log In / Out button

on the Control Panel.

2.

Press the

"1" key

on the numeric keypad five consecutive times. (This is the factory default

"password.")

3.

Press

Enter

on the touch screen.

4.

Press the

Machine Status button

on the Control Panel.

5.

Press the

Tools tab

.

6.

Press

Connectivity & Network Setup

.

7.

Press

Port Settings

.

8.

When the Port Settings menu displays, press the

SMB

selection line.

9.

Press the

Change Settings button

in the lower right corner of the Port Settings menu screen.

10. When the SMB selection menu displays, note that you have only one setting available on a single,

numbered horizontal line. Press this selection line.

11. Press the

Change Settings

button.

12. On the SMB Port Status screen, note which of the two buttons is highlighted as the current setting for

SMB Enablement. The available settings are Enabled or Disabled. To enable SMB at the device,
select the

Enabled

setting.

13. Press the

Save

button on the touch screen, which returns you to the SMB selection menu. (To exit the

screen, without making changes, press the

Cancel

button.)

14. Exit the SMB selection menu and return to the Port Settings menu by pressing the rectangular

Close

button in the upper right corner of the touch screen.

15. Exit the Port Settings menu by pressing the rectangular

Close

button in the upper right corner of the

Port Settings menu screen.

16. To exit the Tools tab screen, wait several seconds for the Auto Clear service to log you out.

«
...
35
36
37
38
39
...
»

Содержание WorkCentre 7300 Series












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WorkCentre 7300 Series

Бренд: Xerox Страницы: 23

Бренд: IBM Страницы: 113

Бренд: IBM Страницы: 16

Бренд: IBM Страницы: 214

Бренд: Canon Страницы: 4

Бренд: Oki Страницы: 104

Бренд: Parkside Страницы: 176

Бренд: Magicard Страницы: 108

Бренд: Magicard Страницы: 124

Бренд: Olivetti Страницы: 149

Бренд: NBS Technologies Страницы: 64

Бренд: Oki Страницы: 188

Бренд: Ricoh Страницы: 301

Бренд: UVP Страницы: 22

Бренд: IBM Страницы: 16

Бренд: Parkside Страницы: 77

Бренд: Ricoh Страницы: 84

Бренд: Compart Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды