Xerox WorkCentre 7300 Series Скачать руководство пользователя страница 199 | Manualshive

Страница: 199 / 203

background image

187

EtherTalk Troubleshooting

Use the following check list to troubleshoot your network communication problem.

Check Physical Media and Network Interface Cards

1.

Verify that the Device is powered ON.

2.

Verify that the Device and Workstation are using the correct cabling to communicate over the network.
Use category 3 UTP patch (NOT crossover) cable for 10 Base T communications, category 5 UTP
patch (NOT crossover) cable for 10 Base T / 100 Base TX communications, and Token Ring cabling
for Token Ring networks.

3.

Verify that the cable at both the Device and Workstation is fully plugged into the Network Interface
Card (NIC). Check the link light, which is typically a green LED, to make sure that it is lit. Typically, but
not always, a second light on the Network Interface Card will be intermittently flashing, indicating the
presence of network traffic. If neither of these lights is lit, there is a problem with the NIC.

Print a Configuration Report at the Device and perform these tasks:

1.

Under the

Ethernet Rated Speed

data label on the Report, verify that your communications speed is

correctly set for your network and that you have a MAC address listed. The driver for your NIC works
at the Media Access Control (MAC) layer of the protocol stack. If no MAC address is shown, you have
either a bad NIC or no NIC at all. Replace or install the Network Interface Card.

2.

Under the

CentreWare Internet Services

data label, verify that this feature is Enabled. If it is NOT,

enable it following the instructions supplied in the

Network Connectivity

section of this guide.

3.

Under the

EtherTalk

data label, verify that the Port is enabled, and that Device has been assigned an

EtherTalk Printer Name and an EtherTalk zone. If one or more of these parameters needs to be
configured, follow the instructions supplied in the

EtherTalk (AppleTalk) Configuration

topic of the

NOS Selection section of this guide.

4.

Under the

EtherTalk

data label and at the bottom of the Configuration Report, verify that

PostScript

is

installed in the Device.  If a PostScript license is installed in the Device, the PostScript logo will be
clearly displayed at the bottom of the Report.  Note: If a PostScript license is NOT installed in the
Device, EtherTalk will NOT be displayed on the Configuration Report, and will be unavailable for
configuration using Internet Services.  Consult your Xerox Representative for assistance.

At the Macintosh workstation

Verify that the Printer is visible in the

Chooser

. If it is NOT, install the Driver and PPD file as stated in the

EtherTalk (AppleTalk) Peer to Peer Printing

topic of the Print Drivers section of this guide.

«
...
197
198
199
200
201
...
»

Содержание WorkCentre 7300 Series












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WorkCentre 7300 Series

Бренд: GCC Technologies Страницы: 14

Бренд: Xante Страницы: 6

Бренд: HPRT Страницы: 2

AccurioPrint 2100

Бренд: Konica Minolta Страницы: 32

WorkCentre M118i

Бренд: Xerox Страницы: 5

3600DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Konica Minolta Страницы: 44

Phaser 6700V/DX

Бренд: Xerox Страницы: 162

Бренд: Kyocera Страницы: 708

Бренд: Xerox Страницы: 2

Бренд: Lexmark Страницы: 13

8560MFPD - Phaser Multifunction Printer Color Laser

Бренд: Xerox Страницы: 20

NanoPrint LM210

Бренд: Arrayit Страницы: 23

Бренд: WOOSIM Страницы: 19

imagePRESS C10010VP

Бренд: Canon Страницы: 40

imagePRESS C6010

Бренд: Canon Страницы: 74

imageFORMULA R40

Бренд: Canon Страницы: 77

Бренд: Canon Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды