manualshive.com logo in svg

Xerox WorkCentre 7300 Series, Руководство администратора

Серия устройств Xerox WorkCentre 7300 - это надежные и многофункциональные принтеры и копировальные аппараты. Для решения любых проблем с устройством, вы можете скачать бесплатно Troubleshooting Manual на manualshive.com. Получите все необходимые инструкции и руководства для работы с вашим принтером.

Поделиться
Скачать
background image

188

Scanning to Hard Drive Troubleshooting 

Use the following check list to troubleshoot your network communication problem.

Before you start

It is assumed that you purchased the Scanning option to enable Scanning to the Hard Drive with your 
Device.  If you did not, contact your Xerox Representative to purchase this option.

Check Physical Media and Network Interface Cards

1.

Verify that the Device is powered ON.

2.

Verify that the Device and Workstation are using the correct cabling to communicate over the network.  
Use category 3 UTP patch (NOT crossover) cable for 10 Base T communications, category 5 UTP 
patch (NOT crossover) cable for 10 Base T / 100 Base TX communications, and Token Ring cabling 
for Token Ring networks.

3.

Verify that the cable at both the Device and Workstation is fully plugged into the Network Interface 
Card (NIC).  Check the link light, which is typically a green LED, to make sure that it is lit.  Typically, but 
not always, a second light on the Network Interface Card will be intermittently flashing, indicating the 
presence of network traffic.  If neither of these lights is lit, there is a problem with the NIC.

Print a Configuration Report at the Device and perform these tasks:

1.

Under the 

Ethernet Rated Speed

 data label on the Report, verify that your communications speed is 

correctly set for your network and that you have a MAC address listed.  The driver for your NIC works 
at the Media Access Control (MAC) layer of the protocol stack.  If no MAC address is shown, you have 
either a bad NIC or no NIC at all.  Replace or install the Network Interface Card.

2.

Under the 

CentreWare Internet Services 

data label, verify that this feature is enabled.  If it is NOT, 

enable it following the instructions supplied in the 

Network Connectivity 

section of this guide.

3.

Under the 

TCP/IP

 data label, determine the method being used to assign TCP/IP addressing to the 

Device.  Verify that the IP Address, Subnet Mask, and Gateway addresses are correct for your network 
and have NOT changed from their previous settings.  Note: The use of DHCP (the DHCP Server) with 
a short "lease" time can cause the Device to be assigned a new IP Address when it is powered off for 
an extended period of time.  This will interrupt communications with workstations using the "old" IP 
address.  If you do not want the IP address to be subject to constant changes, either increase the 
lease time at the DHCP Server, or use the Static IP Addressing method as described in the 

TCP/IP 

Protocol Configuration

 procedure in the NOS selection section of this guide.

At the Device

1.

Verify that you have correctly set up your Mailbox as stated in the 

Setting Up Mailboxes 

section of the 

Scanning to the Device's Hard Drive (Mailboxes)

 topic, in the Options section of this guide.

2.

Scan a test document to your Mailbox as stated in the 

Scanning to Mailboxes

 section of the 

Scanning to the Device's Hard Drive (Mailboxes)

 topic, in the Options section of this guide.

Содержание WorkCentre 7300 Series












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WorkCentre 7300 Series

NEC NEFAX - 691 B/W Laser Introduction Manual preview
NEFAX - 691 B/W Laser
Бренд: NEC Страницы: 20
YOUPAI MAX Product Instruction Manual preview
MAX
Бренд: YOUPAI Страницы: 15
TallyGenicom 5040 Quick Start Manual preview
5040
Бренд: TallyGenicom Страницы: 15
QMS Magicolor 6100 Supplementary Manual preview
Magicolor 6100
Бренд: QMS Страницы: 2
Lanier LD225 Network Manual preview
LD225
Бренд: Lanier Страницы: 150
Samsung CLX-6260ND User Manual preview
CLX-6260ND
Бренд: Samsung Страницы: 368
Canon Pixma iP2580 Quick Start Manual preview
Pixma iP2580
Бренд: Canon Страницы: 12
Canon PIXMA MG5522 Manual preview
PIXMA MG5522
Бренд: Canon Страницы: 18
Canon MultiPASS MPC190 Setup Sheet preview
MultiPASS MPC190
Бренд: Canon Страницы: 8
Oki B4600 Series Specifications preview
B4600 Series
Бренд: Oki Страницы: 2
BenQ CM3700 Series User Manual preview
CM3700 Series
Бренд: BenQ Страницы: 6
Lexmark C782dn Reference Manual preview
C782dn
Бренд: Lexmark Страницы: 4
Avery Dennison 9688 Quick Installation Manual preview
9688
Бренд: Avery Dennison Страницы: 2
aqprox! appPOS80WIFI User Manual preview
appPOS80WIFI
Бренд: aqprox! Страницы: 52
Xante ColourLaser 21 Series Setup Manual preview
ColourLaser 21 Series
Бренд: Xante Страницы: 32
DNP DS-ID400 Settings Manual preview
DS-ID400
Бренд: DNP Страницы: 10
FARGO electronics CardJet X001200 User Manual preview
CardJet X001200
Бренд: FARGO electronics Страницы: 52
Canon iR ADVANCE C5035i Series Manual preview
iR ADVANCE C5035i Series
Бренд: Canon Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды