Network Installation
Xerox ColorQube™ 9201/9202/9203
System Administrator Guide
97
AS400 Raw TCP/IP Printing to Port 9100 (CRTDEVPRT)
This is the procedure to set up printing to a device from an AS400 using the SNMP drivers.
This procedure is intended for users familiar with the AS400 system, especially those experienced with
printing in an AS400 environment.
The AS400 must run V4R5 of OS400 so that the SNMP drivers are present (or V4R3/V4R4 with the
most current PTFs installed).
The device must have port 9100 enabled.
Procedures to Enable Port 9100
1.
At your Workstation, open the web browser and enter the
IP address
of the device in the Address
bar, and press
[Enter]
.
2.
Click the
[Properties]
tab.
3.
If prompted, enter the Administrator User ID and Password. The default is
[admin]
and
[1111]
.
4.
Click on the
[Login]
button.
5.
Click on the
[Connectivity]
link.
6.
Click on the
[Protocols]
link.
7.
Select
[Raw TCP/IP Printing]
in the directory tree.
8.
In the
General
area:
a.
For
Protocol,
check the
[Enabled]
checkbox to enable Raw TCP/IP Printing.
b.
Physical Connection
displays the physical network connection, this will always display
“Ethernet”
.
9.
Up to three ports may be enabled and configured, in the
Port Information
area:
a.
For
Port 1
Leave the
[TCP Port Number]
set to 9100. If two additional ports are available,
click
[Default All]
to see if they set to 9101 and 9102 respectively (emulating HP JetDirect EX
Plus 3).
b.
Leave the
[Bidirectional]
checkboxes and
[Maximum Connections per Port]
settings at their
default values.
c.
Set the
[End of Job Timeout]
to the number of seconds to wait before processing a job
without an End Of Job indicator. The range is from 1 to 65535, and the default is 300.
d.
Leave the
[PDL Switching]
Enabled checkbox at its default value.
Note:
Do not check the
[Enabled]
checkbox for
PDL Switching
, when Windows clients print using
port 9100. this prevents each print job from generating a banner page.
10. Click on the
[Apply]
button to accept the changes or
[Undo]
to return the settings to their
previous values, or
[Default All]
to enter printer defaults for all settings (recommended).
11. Click on the
[OK]
button when you see the message
“Properties have been successfully
modified”
.
Note:
The settings are not applied until you restart the device.
12. Click on the
[Status]
tab, select
[Description & Alerts]
in the directory tree.
Содержание ColorQube 9201
