Network Installation
Xerox ColorQube™ 9201/9202/9203
System Administrator Guide
86
b.
Check the
[Enabled]
checkbox to enable
PDL banner page attributes override LPR control
file attributes for job name and owner
. This feature allows you to replace the standard
information displayed on a banner page, and substitute the user name and job name taken
from the print job.
Note:
Banner pages print if banners are set to
On
at the file server, even if banners are set to Off in
the device.
c.
Select the required option from the
[Place temporary hold on which jobs:]
drop-down menu.
This feature allows you to set the device to hold certain jobs before printing, until the
complete job is received. This delay helps to ensure that the banner page information prints
correctly. Some banner sheet information is contained in the job's control file which may not
always be the first part of a print job the device receives. The following options are available:
•
Only those with data file received 1st
- the device holds the job if the job's data file is
received first. This ensures the device waits to receive the job's control file information so
that the banner sheet contains accurate information.
•
All (consistent with older implementations)
- this option puts all jobs on hold. All data
is received before a job begins to print. This setting can cause jobs to print slowly but will
result in accurate banner sheet information.
•
None (Use printer's default banner sheet job name if data file 1st)
- the device will
not wait to receive the job control information. This selection may cause banner sheet
information to print incorrectly.
10. Click on the
[Apply]
button to accept changes or
[Undo]
to return the settings to their previous
value.
11. Click on the
[OK]
button when you see the message
“Properties have been successfully
modified”
.
Configure SLP
Configure Service Location Protocol (SLP) (if needed to support CUPS, Mac OS, and NetWare).
SLP is used to announce and look up services on a local network. When SLP is enabled, the device
becomes a Service Agent (SA) and announces its services to User Agents (UA) via SLP.
1.
At your Workstation, open the web browser and enter the
IP address
of the device in the Address
bar, and press
[Enter]
.
2.
Click on the
[Properties]
tab.
3.
If prompted, enter the Administrator User ID and Password. The default is
[admin]
and
[1111]
.
4.
Click on the
[Login]
button.
5.
Click on the
[Connectivity]
link.
6.
Click on the
[Protocols]
link.
7.
Select
[SLP]
in the directory tree.
8.
In the
General
area:
a.
For
Protocol,
check the
[Enabled]
checkbox to enable Service Location Protocol (SLP).
b.
Enter an IP address for the
[Directory Agent]
, if required. This will specify the address of a
single Directory Agent (DA) to be added to the list of Directory Agents in the device’s DA list.
Содержание ColorQube 9201
