Wincor Nixdorf TH180 Скачать руководство пользователя страница 79

Страница: 79 / 162

TH180 Programmer’s Guide

GS ^ r t m

[Designation] Execute macro.

[Format]

1DH, 5EH, r, t, m

[Valid limits]

0 r 255

0 t 255

0 m 1

[Initial value] Cleared

[Function] (1) Executes a macro definition.

(2) The parameter r specifies the number of times the macro is executed.

(3) The parameter t specifies the wait time for macro execution.

(4) The parameter m specifies a macro execution mode.

Function

The macro is executed r times at t intervals.

When t time elapses, an LED corresponding to the manual feed
switch flashes to prompt the user to press the switch. The macro

is executed once each time the manual feed switch is pressed. This
is done r times.

(5) When parameter t is specified, processing is on standby for approximately

(t×100 msec) after executing one macro definition.

(6) This command stops defining a macro and clears a macro definition if entered

when a macro is being defined.

(7) If no macro is defined or r = 0, this command is ignored.

(8) The paper switch cannot be operated to advance the paper during macro

execution with m = 1 specified.

(9) Send the (GS :) command to define a macro before and after the contents to

be repeated.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды