Wincor Nixdorf TH180 Скачать руководство пользователя страница 35

Страница: 35 / 162

TH180 Programmer’s Guide

ESC SP n

[Designation] Set right-side character spacing

[Format

1BH, 20H, n

[Valid limits] 0 n 255

[Initial value] n = 0

[Function] (1) Specifies the amount of space to be provided on the right side of a character to

[n×basic calculated pitch] inches.

(2) If the character width-scaling factor of the character exceeds 2, the right-side

spacing will increase based on the scaling factor.

(3) This command does not affect kanji characters.

(4) Right-side spacing can be set up separately for standard mode and page mode.

(5) The basic calculated pitch is set up using the Set horizontal and vertical motion

unit (GS P).

In addition, the specified right-side spacing will not be changed even if the
basic calculated pitch is changed using the Set horizontal and vertical motion

unit (GS P) after the right-side spacing has been setup.

(6) If the calculation result contains a fraction, the value is corrected using the

minimum pitch of the mechanism. The remainder is then discarded.

(7) In standard mode, the horizontal motion unit (x) is used.

(8) In page mode, the operations given below are executed based on the starting

point:

a. The print position is moved in the paper feed direction if the starting point

has been specified as upper left or lower right using the Select print
direction in page mode command (ESC T). At this time, the vertical motion

unit (x) is used.

b. If the starting point has been specified as upper right or lower left using the

Select print direction in page mode command (ESC T), the print position is

moved in a direction perpendicular to the paper feed direction. At this
time, the horizontal motion unit (y) is used.

(9) The maximum specifiable right-side spacing is about 31.875 mm (255/203

inches). The specified value beyond the maximum one is rounded down to the
maximum value.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды