Wincor Nixdorf TH180 Скачать руководство пользователя страница 105

Страница: 105 / 162

TH180 Programmer’s Guide

100

b. When n = 2, 50 (drawer kick connector)

Bit

Function

Value

State of drawer1 kick connector pin 3

Low

High

To be defined

---

State of drawer2 kick connector pin 1

Fixed at 1(High)

To be defined

---

Not used

Fixed at 0

To be defined

---

To be defined

---

Not used

Fixed at 0

(3) Roll paper end detector (n=1,49) is paper present (b3 = 0, b2 = 0) when the

cover is open.

(4) After the mechanics operation ends, status is transmitted.

(5) After the host is confirmed to be ready to receive status information, this

information is transmitted to the host if the DTR/DSR protocol is used. If the

host is not ready to receive, transmission of the status information is deferred
until the host is ready.

(6) If the XON/XOFF protocol is used, status information is transmitted to the host

without checking whether the host is ready to receive.

(7) A delay may occur between command reception and status transmission

depending on the condition of the reception buffer because this command is
executed during print buffer expansion.

(8) The status of this command and the ASB status must be identified.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды