Wincor Nixdorf TH180 Скачать руководство пользователя страница 59

Страница: 59 / 162

TH180 Programmer’s Guide

ESC \ nL nH

[Designation] Set relative print position

[Format]

1BH, 5CH, nL, nH

[Valid limits]

0 nL 255

0 nH 255

[Initial value] ---

[Function] (1) Specifies the next print start position using the print position relative to the

current position, which is the origin.

(2) The position moved [(nL+nH×256)×basic calculated pitch] inches from the

current position is the next print start position.

(3) A position specified out of the print area is ignored.

(4) A positive number is used to specify a position to the right of the current print

position. A negative number is used to specify a position to the left of the

current print position.

(5) Negative numbers are displayed as complements of 65536.

For example, for N-pitch movement to the left,

nL+nH×256=65536 - N.

(6) The basic calculated pitch is set up using the Set horizontal and vertical motion

unit (GS P).

(7) If the calculation result contains a fraction, the value is corrected using the

minimum pitch of the mechanism. The remainder is then discarded.

(8) In standard mode, the horizontal basic calculated pitch is used.

(9) In page mode, the operations given below are executed based on the starting

point:

a. The print position is moved in the paper feed direction if the starting point

has been specified as upper left or lower right using the Select print
direction in page mode command (ESC T).

At this time, the vertical motion unit (x) is used.

b. The print position is moved in a direction perpendicular to the paper feed

direction if the starting point has been specified as upper right or lower

left using the Select print direction in page mode command (ESC T). At this
time, the horizontal motion unit (y) is used.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды