Wincor Nixdorf TH180 Скачать руководство пользователя страница 106

Страница: 106 / 162

TH180 Programmer’s Guide

101

ESC u n

[Designation] Transmit peripheral device status

[Format

1BH, 75H, n

[Valid limits] n = 0

[Initial value] ---

[Function] (1) Transmits peripheral device status data (one byte length) corresponding to the

connector pin specified by n.

Function

Specifies the No.3 pin of the drawer kick connector.

(2) The table below lists the status data transmitted.

Bit

Function

Value

State of drawer kick connector pin 3

Low

High

To be defined

---

To be defined

---

To be defined

---

Not used

Fixed at 0

To be defined

---

To be defined

---

Not used

Fixed at 0

(3) This command is valid only for serial interface and USB(VCOM) interface

specifications.

(4) When the DTR/DSR protocol is used, the printer transmits status data after

confirming that the host is ready to receive data. When the host is not ready to

receive data, the printer waits until the host is ready.

(5) When the XON/XOFF protocol is used, the printer transmits status data without

confirming that the host is ready to receive data.

(6) Since this command is processed during print buffer expansion, a delay may

occur between command reception and status data transmission depending on

reception buffer status.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды