Wincor Nixdorf TH180 Скачать руководство пользователя страница 78

Страница: 78 / 162

TH180 Programmer’s Guide

Commands related to macro functions

GS :

[Designation] Start/end macro definition

[Format]

1DH, 3AH

[Valid limits] ---

[Initial value] Cleared

[Function] (1) Specifies to start or stop a macro definition.

(2) This command specifies to start a macro definition when entered during

ordinary operation. If the command is entered when a macro definition is

already started, it specifies to stop the macro definition.

(3) If an Execute macro (GS ^) command is entered when a macro is being defined,

this command stops defining the macro and the macro definition being made is

cleared.

(4) Initially, no macro is defined.

(5) No macro definition is cleared by the Initialize printer (ESC @) command.

(6) If this command (GS :) is entered twice consecutively, a macro becomes

undefined.

(7) A macro definition can define up to 2048 bytes of data.

Data exceeding 2048 bytes cannot be defined.

(8) The Real-time status transmission (DLE EOT) command cannot be

defined in a macro.

(9) In the case of the following, the macro that I defined is cleared.

a. Print a raster bit image command (GS v 0).

b. Print in NV bit mode image command (FS q).
c. Switch off the printer.

d. Reset command.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды