Wincor Nixdorf TH180 Скачать руководство пользователя страница 119

Страница: 119 / 162

TH180 Programmer’s Guide

114

DLE DC4 n m t

[Designation] Real-time output of designated pulse

[Format]

10H, 14H, 01h, m, t

[Valid limits] 0 m 2

1 t

[Function] (1) m corresponds to the designated connector pin and t outputs the designated signal in real time.

Designated connector pin

Drawer kick connector No. 2 pin

Drawer kick connector No. 5 pin

Buzzer

(2) The on/off time is respectively set as t x 100 ms.

(3) This command is ignored in the following states:

During the signal output to the drawer kick connector

During the occurrence of error

(4) If the code sequence that matches the codes that make up this command is received, the user must

note that the same operation as the operation for this command will take place.

Example: If the relevant code sequence is included in bit image data.

(5) This command must not be inserted between other command codes for use.

Example: If this command is used in the bit image data.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды