Wincor Nixdorf TH180 Скачать руководство пользователя страница 107

Страница: 107 / 162

TH180 Programmer’s Guide

102

ESC v

[

Designation] Transmit paper detector status

[Format]

1BH, 76H

[Valid limits] ---

[Initial value] ---

[Function] (1) Transmits paper detector status data (one byte length) as shown below.

Bit

Function

Value

Roll paper near-end detector

With paper

Without paper

Roll paper near-end detector

With paper

Without paper

Roll paper end detector

With paper

Without paper

Roll paper end detector

With paper

Without paper

Not used

Fixed at 0

Not used

Fixed at 0

Not used

Fixed at 0

Not used

Fixed at 0

(2) This command is valid only for serial interface and USB (V-COM) interface

specifications.

(3) When the DTR/DSR protocol is used, the printer transmits status data after

confirming that the host is ready to receive data. When the host is not ready to
receive data, the printer waits until the host is ready.

(4) When the XON/XOFF protocol is used, the printer transmits status data without

confirming that the host is ready to receive data.

(5) Since this command is processed during print buffer expansion, a delay may

occur between command reception and status data transmission depending on
reception buffer status.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды