Wincor Nixdorf TH180 Скачать руководство пользователя страница 111

Страница: 111 / 162

TH180 Programmer’s Guide

106

ESC L

[Designation] Select page mode

[Format]

1BH, 4CH

[Valid limits] ---

[Function] (1) Switches from standard mode to page mode.

(2) This command is valid only when entered at the beginning of the line.

(3) This command is ignored if entered in page mode.

(4) The commands given below return to standard mode:

a. After printing is finished using the Print and return to standard mode in page

mode command (FF).

b. Upon receiving the Select standard mode command (ESC S).

(5) In the print area specified using the Set printing area in page mode command

(ESC W), the point specified using the Select print direction in page mode

command (ESC T) becomes the character expansion position.

(6) For the commands given below that have separate values for page mode and

standard mode, the setting values are switched to those of page mode:

a. Set right-side character spacing command (ESC SP)

b. Set kanji spacing command (FS S)
c. Select 1/6-inch line spacing command (ESC 2)

d. Set line spacing command (ESC 3)

(7) For the commands given below, the settings are valid only in page mode:

a. Turn 90°clockwise-rotation mode on/off (ESC V)

b. Select justification command (ESC a)
c. Turn upside-down printing mode on/off (ESC )
d. Set left margin command (GS L)
e. Set printing area width command (GS W)

(8) The Initialize the printer command (ESC @) returns to standard mode.

(9) The data over bottom margin are discarded.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды