Wincor Nixdorf TH180 Скачать руководство пользователя страница 41

Страница: 41 / 162

TH180 Programmer’s Guide

ESC ? n

[Designation] Cancel user-defined characters

[Format]

1BH, 3FH, n

[Valid limits] 32 n 126

[Initial value] ---

[Function] (1) Erases a character user-defined for a specified code.

(2) n is a character code corresponding to a definition pattern to be deleted.

Once the definition pattern is deleted, the same pattern as for the internal
corresponding character is printed.

(3) The specified code definition pattern of the character font selected using the

Select print mode(s) (ESC !) in print mode is deleted.

(4) If a specified character code has not been defined, this command is ignored.

ESC E n

[Designation] Turn emphasized mode on/off

[Format]

1BH, 45H, n

[Valid limits] 0 n 255

[Initial value] n = 0

[Function] (1) Specifies or cancels emphasized printing.

(2) The table below lists the bit definitions:

Bit

Function

Value

Emphasized printing

Cancel

Specify

To be defined

7 To be defined

(3) For parameter n, only the lowest-order bit is valid.

(4) Also, emphasized printing can be specified using the Select print mode (ESC !).

However, the most recently executed command is valid.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды