Wincor Nixdorf TH180 Скачать руководство пользователя страница 36

Страница: 36 / 162

TH180 Programmer’s Guide

ESC ! n

[Designation] Select print mode(s)

[Format]

1BH, 21H, n

[Valid limits] 0

255

[Initial value] n = 0

[Function] (1) Batch-specifies print mode.

(2) The table below lists the bit definitions:

Bit

Function

Value

0 Character font

Font A is selected.

Font B/C is

selected.

To be defined

Emphasized printing

Cancel

Specify

Double character height

Cancel

Specify

Double character width

Cancel

Specify

To be defined

7 Underline

Cancel

Specify

(3) If both a double character height (bit 4 = 1) and a double character width (bit 5

= 1) are simultaneously specified, the character size quadruples.

(4) If underlining is specified, an entire character position, including the

character's space specified by the Set right-side character spacing(ESC SP), is

underlined. However, apparent space, which is generated using a horizontal
tab, is not underlined. In addition, turn 90°clockwise rotation mode ON (ESC

V) are not underlined.

(5) The thickness of the underline is not related to the character. The thickness

specified using the Turn underline mode on/off command (ESC -) is used.

(6) The character base lines are justified if characters with different character

height scaling factors are present on the same line.

(7) Also, emphasized printing can be specified using the Turn emphasis mode

on/off command (ESC E). However, the most recently executed command is
valid.

(8) Also, underlining can be specified using the Turn underline mode on/off (ESC -)

command. However, the most recently specified type is valid.

(9) Also, the character size can be specified using the Set character size command

(GS !). However, the most recently executed command is valid.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды