Wincor Nixdorf TH180 Скачать руководство пользователя страница 116

Страница: 116 / 162

TH180 Programmer’s Guide

111

a. First byte = 40H
b. Second byte = 40H

(5) After the host is confirmed to be ready to receive (the DSR signal is in a space

state) a printer ID, a printer ID is transmitted to the host if the DTR/DSR

protocol is used. If the host is not ready to receive (the DSR signal is in a mark
state), transmission of the printer ID is deferred until the host is ready.

(6) If the XON/XOFF protocol is used, a printer ID is transmitted to the host without

checking whether the host is ready to receive.

(7) A delay may occur between command reception and printer ID transmission

depending on the condition of the reception buffer because this command is
executed during print buffer expansion.

(8) If ASB has been enabled using the Enable/disable automatic status back

command (GS a), the printer ID of this command and the ASB status must be
identified.

(9) This command is ignored if parameter n is outside the definition area.

Содержание TH180



































































































































































Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды

Wincor Nixdorf TH180, Руководство программиста

Результаты поиска

Содержание TH180

Отзывы:

Похожие инструкции для TH180

Бренды по названию

Популярные бренды