Wfly ET08 страница 78 Скачать руководство пользователя

Страница: 78 / 84

Throttle Curve

Interface path: HOME/MON. → [MODEL MENU] → [Throttle Curve]

Adjust the throttle output curve according to the action of the throttle rocker through the seven-point

curve, so that the engine (motor) revolution can reach the optimal state of ﬂight.

Note: Start the engine in normal mode at normal idle.

* Fly mode: set "Fly Mode" control switch in "Model Menu" → "Condition".Switch through the switch,

respectively for function setting.

Set instructions

The curve control switch of throttle hold should be set in [MODEL MENU] → THROTTLE GOLD].

There're 7 curve reference point

Adjust the overall oﬀset of the selected curve reference point, and

press ok to switch the reference point (long press to reset value).

Adjust the center point of the curve to move up and down.

Adjust the ratio of output value of left and right curves respectively.

Condition controls the pitch curve, and diﬀerent modes are

enabled for curve adjustment when setting.

WARNING

When starting the engine, be

sure to start it in normal mode

at a normal idle speed.

MODEL MENU \ MULTICOPTER

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды