manualshive.com logo in svg

Wfly ET08, Инструкция по эксплуатации

Поделиться
Скачать
Wfly ET08 Скачать руководство пользователя страница 69

THROTTLE CUT

The selected hardware cut switch adjusts the ratio value when the throttle and throttle lever are idle 

down, until the engine can be completely shut down.

Safely and easily to turn off the engine. Throttle cut provides an easy way to stop the engine from 

running. Generally speaking, it can be realized by dialing a hardware switch in an idle state. This function 
cannot be triggered when the throttle is high to prevent any misoperation. The position and direction of the 
switch must be selected because the initial setting is [--].

Interface path: HOME/MON.→ [MODEL MENU]→[THROTTLE CUT]

* When both [Throttle Hold] and [Throttle Cut] are enabled, the function of [Throttle Hold] has the highest 

priority.

In addition, verify that the throttle link is not tightened or that the servo is not overloaded.

2 Click the “Switch” button to pop up the “Switch Assignment” interface and select the control switch.

1 Status is switched to "ACT”

3 Turn on the selected “cut control switch”, the engine stick is in the idle down state, adjust the rate until 

the engine (motor) stops completely.

* Fly Mode: set "Fly Mode" control switch in "Model Menu" → "Fly Condition".Switch through the switch, 

respectively for function setting.

Please pay attention to the throttle connection here, do not let the servo exceed the travel.

Cut position setting

The set cut position

Current position of throttle stick

Function control, default [--]

Range 0%-50%, default 17%
Press the left and right keys 

to adjust the value or press the 
ok key to intercept the position 
parameters of the STICK.

Set the throttle trigger position

69

MODEL MENU \ AIRPLANE

DANGER

The "cut position" must not 

be set higher than the lowest 

speed of throttle position. It is dangerous if the 
engine runs at high speed.

Содержание ET08





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды