Wfly ET08 страница 73 Скачать руководство пользователя | Manualshive

Страница: 73 / 84

background image

WINGLET

Interface path: HOME/MON. → [MODEL MENU] → [WINGLET]

This function is used to adjust the left and right rudder of the model winglet. The winglet is used to reduce

the induced drag caused by the wing tip vortex. (Winglets are vertical or angled extensions at the end of
each wing.)

The winglets can signiﬁcantly increase the wing's aspect ratio without increasing the structural stress

and weight of the wing. Although increasing the span is also able to reduce the induced drag, it also
introduces parasitic drag and requires more power to support the weight of the wing, which results in no
overall savings. The winglet can help solve this problem, it increases the aspect ratio, but does not
increase the wing's wingspan.

Function state switch (INH, ACT, default [INH])

● When the connection causes the mixing direction to be reversed, it can be adjusted by changing the

●

The amount of operation of each servo can be adjusted separately. (For the connection method of the

steering gear, please refer to "Servo connection in diﬀerent model categories")

polarity (+/-) of the action amount.
● When the amount of action is too large or the rudder is repeated, the servo may not respond. Be sure to

conﬁrm the actual movement of the body when setting

Adjust the action amount of rudder respectively,
the default is 100%

Rudder

(Winglet)

Tailless aircraft

Rudder2

(Winglet)

Tailless aircraft

73

MODEL MENU \ AIRPLANE

«
...
71
72
73
74
75
...
»

Содержание ET08





















































































Отзывы:

Нет отзывов

Похожие инструкции для ET08

Бренд: SOMFY Страницы: 24

AVO-A4-WP110-EU

Бренд: Intelix Страницы: 4

Бренд: Jung Страницы: 5

Бренд: Vaisala Страницы: 101

Ipify EUP-2704R-4T-PKG

Бренд: Intercoax Страницы: 2

Бренд: Yaesu Страницы: 17

Бренд: HBM Страницы: 108

exta life RNK-22

Бренд: Zamel Страницы: 8

Penntek Preliminary TR-45L

Бренд: WA3RNC Страницы: 5

Бренд: TTI Страницы: 39

Бренд: Camel-RF Страницы: 7

Бренд: POLMAR Страницы: 32

Бренд: Sailor Страницы: 104

Бренд: Conceptronic Страницы: 58

Бренд: Micron Страницы: 4

Бренд: Abexo Страницы: 28

Бренд: Data Industrial Страницы: 13

Бренд: MTHTrains Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды